Separate ways

Hamworthy Heating, Andrew Dabin, heating, boiler, no flow, hyrdaulic separation, buffers, low loss headers, open-vented heating system
Andy Dabin

Andrew Dabin explains hydraulic separation methods for heating system refurbishment and why they are so important to consider.

Open-vented heating systems used to be the industry standard. But due to their nature, oxygen ingress will result in corrosion and sludge build-up over the years, even with regular maintenance. This can cause the heating system to become unreliable and force a boiler replacement. In this article, we look at different methods to connect the new equipment to an existing system, considering the improvement of reliability and maintenance.

An assessment of the current system is vital before the installation of any new product. The aim of this survey is to establish what is required to prevent the new boiler(s) from being negatively affected by existing system conditions. This may include but is not limited to:

• System cleansing and/or flushing

• Removal of old pipework and valves

• Update of the existing system layout to include filtration/cleaning etc

• Evaluating whether the new installation can be sealed or open vented

A first point of examination is the condition and size of current pipework. For optimum performance and efficiency such as enabling the required lower return temperatures for condensing performance, alterations need to be considered. When it comes to the water flow around the system, it is necessary to see whether the boiler has an integral pump and if a primary circuit pump is required. Does the current pipework’s flow capacity match the primary/shunt pump minimum requirements?

Possible consequences of an inadequate flow rate are not only annoying for the client but can also be costly. A broken heat cell due to an insufficient water supply costs thousands to repair. A scaled-up heat exchanger causes efficiency losses and longer heat-up times as well as a shorter life expectancy. As commercial boilers are a large capital investment, it makes sense to assess what they are linked to.

It’s important to ask how you are going to protect your boilers. It is worth considering the installation of 1) a dosing pot for introducing chemicals (e.g. to prevent corrosion) into the system; 2) an air and dirt separator to remove air bubbles and dirt particles; and 3) strainers to catch debris, or the inclusion of a sidestream filter.

The next step is choosing how to connect to the secondary circuit. This can be achieved with a low loss header or buffer vessel arrangements; plate heat exchangers; or the use of a no flow boiler.

Low loss headers or buffers

Low loss headers are also referred to as common headers and are available as different types: horizontal, vertical and some have dual action with combined air and dirt separators.

Using a low loss header or buffer vessel in a heating system ensures adequate flow, resistance and temperature around the primary circuit, while flow rates and temperatures in the secondary circuit may vary.

Hamworthy Heating, Andrew Dabin, heating, boiler, no flow, hyrdaulic separation, buffers, low loss headers, open-vented heating system

Another benefit when using a vertical low loss header is the low flow velocity allowing sludge to sink to the bottom which can then easily be removed from the system via a trap. They are often supplied as part of a package directly from a manufacturer correctly sized to suit the chosen boiler’s connections.

However, alteration costs on an old heating system to include a low loss header or buffer vessel can prevent using this choice. Other factors could be space requirements and an insufficient number of ports (depending on how many heating circuits you want to connect to it).

Plate heat exchangers

Plate heat exchangers provide hydraulic separation of heating circuits and protect new boilers from dirt and debris from an existing secondary circuit, as the water does not mix. Several types of heat exchangers are available. While brazed heat exchangers can’t be taken apart, gasketed types can be fully maintained and increased in duty (depending on the frame size) for future extension of the heating circuit. Domestic hot water plate exchangers are solely for the purpose of providing hot water – hence for a different temperature profile and different controls.

Benefits include the protection of boilers through separation which prolong their life. A reduced amount of water in the primary circuit means treatment becomes cheaper (less chemicals used). Additionally, they provide pressure protection. However, if the secondary circuit is open vented, this side of the system may still require the same cleansing and maintenance approach as the primary circuit to prevent the plate heat exchanger from failing.

Downsides are space issues when both heating circuits are pressurised, and two pressurisation units needed. While it is common practice to use several boilers to prevent a single point of failure, only using one plate heat exchanger would reintroduce this risk. The use of high micron filters to catch debris in the system and additional maintenance are also recommended.

No flow boilers

A no flow boiler on the primary circuit is non-dependent on the secondary circuit flow for safe operation. Instead, an internal variable speed circulation circuit ensures water movement when circuit pumps are off or set to low. Furthermore, it utilises differential temperature supervision to control the output power for safe operation. The high water content in a no flow boiler equals high thermal mass which allows it to fire without flow and without risk of overheating. Once the control stat stops the boiler, the thermal mass safely absorbs residual heat. These types of boilers often have dedicated return connections for low temperature and high temperature heating circuits to ensure maximum efficiency can be obtained.

The main benefit of installing a no flow boiler is that it removes the need to install it in a dedicated primary circuit as well as the installation of additional equipment such as low loss header, plate heat exchanger and pumps. Thanks to its high water capacity, it can operate with wide differential temperatures and the high and low temperature circuits connect to dedicated heat exchanger return connections.

What speaks against choosing a no flow boiler is the required flow isolation through non-firing boilers. This helps the system pumps to modulate which ensures flow through the firing boiler. Isolating any non-firing boiler in any system is good practice.

Furthermore, the boiler should not be operating using its own thermostats or integral temperature controls but instead be integrated using a sequence controller or building management system. This improves overall boiler control for many boiler types. Space limitations (access) and weight must be taken into consideration with this option as the boilers are often larger.

Which method of hydraulic separation is preferable will be mostly determined by available plant room space, time, and budget. Depending on the choice, other considerations would be low loss header/heat exchanger sizing; type of pump(s) used; and if a reverse return is required.

On the one hand, hydraulic separation can be achieved by using low loss header or plate heat exchanger. This offers flexibility, as this equipment is optional. On the other hand, opting for a no flow boiler means the most integral part of the heating system determines the remaining design considerations.

Andrew Dabin is product manager for Hamworthy Heating

Related links:
Related articles:



modbs tv logo

LG supports fast-moving WeWork project

How LG Air Conditioning helped WeWork London achieve a fast project with great results.

MBStv at the BESA National Conference 2019

The BESA National Conference 2019 saw over 200 delegates gather to discuss the industry’s challenges and opportunities. MBStv was there to capture it all.