High-efficiency condensing water heaters — paradox or paradigm?

fig 1
Fig. 1: By passing flue gases through several heat exchangers, the efficiency of generating domestic hot water is maximised.
Domestic hot water stored at 60°C or more and condensing water heaters (where the return temperature has to be below about 55°C) might seem a paradox. So how can condensing water heaters be included in the Government’s Energy Technology List. PAUL MARSDON explains.Independent gas-fired condensing water heaters have recently been included in a distinct sub-heading under boilers in the Government’s Energy Technology List, in recognition of their energy saving capabilities. In principle, this makes sense, given that the demand for domestic hot water is not seasonal and, generally, is increasing in modern commercial buildings, whilst the reverse is generally true for space heating. However, in practice, can a water heater provide the efficiencies of condensing operation at the lower return temperatures necessary yet supply hot water at the elevated temperatures required for its use and to prevent formation of bacteria such as legionella? Contradiction Despite this apparent paradox, there is no contradiction in terms when referring to a ‘high-efficiency condensing independent gas-fired water heater’. So how does this type of appliance produce hot water at an acceptable temperature and operate in condensing mode? This can happen in different ways, according to the technology adopted by the manufacturer and is also influenced by the type of water heater — for instance whether it is a non-storage or storage unit. Domestic-hot-water services for commercial and public buildings need to be supplied at a safe set temperature limit somewhere above 60°C. To comply with regulations for preventing legionella, stored hot water should not fall below this temperature, and the system return temperature should not fall below 54ºC.
Fig. 2:The efficiency of condensing water heaters is enhanced using designs that minimise the temperature of the return water and maximise the condensing time.
However, a condensing boiler will be more efficient if the flow temperature and the return temperature are lower. In that case, the flue-gas temperature will also be reduced, possibly to the point of water vapour in the flue gases condensing, thus recovering more latent heat. The out-going flue-gas temperatures are normally twice the return-water temperature — although this does not mean the extra benefits of a condensing water heater cannot be realised when operating at 60ºC. The Andrews non-storage condensing water heater, for example, has a pre-mix water-cooled burner that reduces the flame temperature to provide a more efficient flame and, incidentally, very low emissions of oxides of nitrogen and carbon dioxide. After ignition, the flue gases are forced through a further three heat exchangers before entering the secondary flue. Each time the flue gases pass through a heat exchanger, the heat or energy is passed from the combustion flame into the waterways (Fig. 1). For example, before passing through the first heat exchanger, the combustion temperature is about 1200°C. As the gases pass through this exchanger, the flame temperature is reduced to 700°C. When the gases pass the second heat exchanger the flame temperature is further reduced to 140ºC. After passing the third heat exchanger, the flame temperature is about twice the return-water temperature. As the flame temperature is reduced, the heat or energy is transferred into the waterways. The burner for this range of water heaters fully modulates between 20% and 100%, depending on the load. This allows the flame temperature to be reduced at part load whilst permitting a fall in flue temperature sufficient to produce condensate, increasing efficiency. The low water content of these appliances means conditions conducive to the formation of legionella bacteria are virtually eliminated. Two approaches The most common way of operating condensing storage water heaters incorporates either upward- or downward-firing high-efficiency burners within a combustion chamber located inside the storage tank. Whilst efficient, the condense time of this method is limited as the whole tank is being heated, and because heat is also transferred through the flue tube (again located inside the storage tank) to the stored water.
Fig. 2:The efficiency of condensing water heaters is enhanced using designs that minimise the temperature of the return water and maximise the condensing time.
The concept used by Andrews for delivering high efficiency ratings from its most recently introduced condensing storage water heater range (Fig. 2) is based on the stainless-steel tank being heated by one or more externally mounted burner modules, each containing a pre-mix burner within a stainless-steel heat exchanger (Fig. 3). It operates according to the loading principle, with the water in the bottom of the tank being fed directly through the heat exchanger, heated up and carried back to the top of the tank.
Fig. 2:Fig. 3:The reality of high-efficiency condensing water heating — external burner modules heat cold water drawn from the bottom of the storage tank and deliver it to the top.
Mains cold water enters into the bottom of the storage tank via a dip tube. When draw-off occurs, water enters the external heat exchanger/s via a tapping at the base of the tank. Because this water is supplied at around 10ºC (typical design supply temperature and well below the 55ºC required for condensing to occur) the water heater will operate in condensing mode whilst it raises the temperature of the stored water (typically 200 to 300 litres) to the 60°C set point. During the final heating period, which takes no more than a few minutes and occurs when about 80% of the contents of the tank is at the set point of 60°C, water supplying the heat exchanger/s increases in temperature from its typical 10°C up to the 60°C tank set point. It is at this stage that the heat exchanger/s start to modulate down and stop condensing as they go to standby mode. Because the water is being circulated from the lowest point in the tank, the whole tank is heated up, and there are no cool zones. This system therefore prevents conditions occurring that would harbour legionella bacterium. Moreover, the storage-tank temperature of this appliance can be re-set by means of a remote time clock to allow operation of an anti-legionella flushing programme throughout the hot water distribution pipework. Paul Marsden is with Andrews Water Heaters, Wednesbury One, Black Country New Road, Wednesbury, West Midlands WS10 7NZ.
Related links:



modbs tv logo

New Sustainability Director for Wates Group

Wates Group, a family-owned development, building and property maintenance company, has appointed Cressida Curtis as its new Group Sustainability Director.

Domus Ventilation appoints new contractor sales managers

Ventilation systems manufacturer Domus Ventilation has announced the arrival of three new Contractor Sales Managers.